Lanterns for control panel illumination
Illumination of devices
In this section it is a question of illumination of display devices. The description of the control bulbs also located in the combined device, you will find Tools and devices in the head. Dismantle of illumination of devices:
|
|
- Dismantle a steering wheel (the head the Suspension bracket of wheels and a steering).
- Dismantle the combined device (the head Tools and devices).
- Behind the combined device depending on model about nine cartridges of bulbs for illumination of devices are visible.
- For replacement turn them to the left and take out.
- Bulbs with a glass socle on 1,1 Vt form one constructive element with a cartridge.
- Again insert into the combined device a cartridge with a lamp and turn to the right against the stop.
- In cars with the onboard computer for display illumination five bulbs with glass socles on 1,1 Vt are used.
- Some bulbs for illumination of devices – depending on the manufacturer – are supplied by orange protective caps. Caps can be established on new lamps накаливания.
|
|
At the left: lateral illumination of a luggage carrier to identically top illumination of a luggage carrier. By an arrow the assembly aperture for the case of a lantern (1) is shown; figure "2" designates a lamp накаливания.
On the right: for illumination of a regulator of heating the small bulb (1) serves. Through one optical path (2; here will take out from clips) illumination is distributed on all three scales of handles of adjustment.
|
|
For illumination of knot of a hand control by climatic installation four small bulbs are used. The cartridge and a bulb form one constructive element with which it is possible to replace by means of a screw-driver (turn on a turn quarter to the left). |
|
|
Lantern of a box for gloves: cautiously wring out a screw-driver the case (2) bulbs from an assembly aperture. After that there is accessible софитная a lamp накаливания (1). |
|
|
Dismantle of the case of an ashtray/prikurivatelja: open an ashtray (2), a screw-driver (1) take out from spring grooves in both dredging (arrow) and extend the case back. |
|
|
Here the bulb of illumination of an ashtray/prikurivatelja (2) is removed with прикуривателя (1) at the case of an ashtray dismantled and turned by an underside. |
Illumination of the lever of heating
|
|
- Dismantle a radio receiver (the head Tools and devices).
- Loosen the in an assembly aperture of a radio receiver four screws.
- Remove the decorative panel of the average console (switches remain on a place).
- Pull back all three rotary regulators of heating/ventilation.
- Unscrew under them two screws with crosswise heads, remove the decorative panel.
- Take out from clips an optical path.
- Now the bulbs inserted here with glass socles on 1,2 Vt are visible.
- Bulbs can be taken out on one of a cartridge.
|
|
Illumination of knot of a hand control by climatic installation
|
|
- Take out from clips a radio receiver (the head Tools and devices).
- Loosen the in an assembly aperture of a radio receiver four screws.
- Remove the decorative panel of the average console (switches remain on a place).
- Unscrew four fixing screws of knot of a hand control climatic installation and take out knot.
- On an underside turn to the left cartridges of lamps and take out them.
- Bulbs with glass socles on 2 Vt form one constructive element with a cartridge.
- At both average bulbs the black border, at both external – is not present.
|
|
Ashtray/prikurivatelja illumination ahead
|
|
- Open an ashtray (2) in the average console.
- Insert a screw-driver into one of two dredging behind an ashtray and wring out downwards on the basis of the ashtray case a fixing spring.
- It is easier for making if to shine a manual small lamp in dredging.
- Repeat the same process with the second spring.
- Take out back an ashtray together with the case.
- Raise a small fixing overlay, take out a lamp cartridge on прикуривателе.
- Replace a lamp.
|
|
Lantern for illumination of a box for gloves
Pressure on a bulb for illumination of a box for gloves arrives at the included lay or dimensional lanterns. It joins and switched off by the contact switch in the hinge.
|
|
- Open a box for gloves.
- Insert a screw-driver into dredging sideways on the case of a lamp and cautiously wring out a lamp.
- After lamp replacement накаливания (софитная a bulb of 5 Vt, length of 36 mm) again insert the lamp case, in the beginning that party, where a wire.
|
|
The transfer indicator
For illumination of the indicator of transfer on the lever-selector of an automatic transmission the lamp with a glass socle (1,2 Vt, form W under the standard of DYNES) serves.
|
|
- Dismantle the average console (the head Salon).
- Take out from clips a lamp cartridge at the left on the lever-selector console.
- Take out a lamp with a glass socle from a cartridge.
|
|
Bulbs in switches
Almost in all switches there are shined symbols, but this illumination is not intended for replacement. Therefore in case of defect it is necessary to consider the dark switch or to replace it.
|