Audi A4

Since 1994 of release

Repair and car operation



Audi А4
+ Running gear
+ Regular servicing
+ Engines
+ Turbo-supercharging
+ Exhaust system
+ Cooling system
+ Fuel tank and the fuel pump
+ The air filter and channels всасывания
+ Injection system
+ Coupling
+ Transmission and the main transfer
- Suspension bracket of wheels and steering
   Running gear
   Check of cuffs of the steering mechanism
   Check of dustproof caps and backlash in heads of cross-section steering draught
   Check of dustproof caps of hinges of an axis
   Check люфта a steering wheel
   Check клинового a belt
   Check of level of oil
   Check of a backlash of the wheel bearing
   Shock-absorbers
   Check of shock-absorbers
   The help at malfunctions
   Adjustment of wheels
   Measurement of adjustment of wheels
   The help at malfunctions
   Independent works on a running gear and a steering
   Dismantling of a suspension bracket of forward wheels
   Works with the back bridge
   Shock-absorber replacement behind
   Steering
   Works on a steering
   Tightness check сервоуправления
   Poliklinovoj belt
   The help at malfunctions
   Adjustment of the steering mechanism
   Pump dismantle сервоуправления
   Filling and system prorolling сервоуправления
   Safety pillow
   Safety instructions
+ Brakes
+ Wheels and tyres
+ The electrotechnical equipment
+ Ignition system
+ Illumination
+ The alarm equipment
+ Tools and devices
+ Heating and ventilation
+ Body details
+ Salon
Search of malfunctions
Technical characteristics










Works on a steering

The external end of cross-section steering draught

1 – an adjusting bolt of a convergence of wheels on turn;
2 – tightening a bolt of cross-section steering draught;
3 – a head of cross-section steering draught;

4 – a counternut;
5 – шестигранник cross-section steering draught.


The arrow specifies in assembly position of an adjusting bolt of the steering mechanism.

Replacement of a head of cross-section steering draught

 PERFORMANCE ORDER

  1. Remove a wheel.
  2. Unscrew самоконтрящуюся a nut on a tightening bolt of cross-section steering draught.
  3. Take out tightening a bolt.
  4. Unscrew an adjusting bolt of a convergence of wheels on turn.
  5. Squeeze out a head of cross-section steering draught downwards from сошки a wheel on the case of the wheel bearing.
  6. Unscrew a counternut on a head of cross-section steering draught, wring out thus шестигранник cross-section steering draught in an opposite direction.
  7. Designate position of screw connection of cross-section steering draught then after свинчивания the width of a track will be approximately the same.
  8. Unscrew a head of cross-section steering draught, transfer marks on a new head of steering draught.
  9. Installation: press a finger of a head of cross-section steering draught in сошку a wheel if it is necessary, cautiously hammer.
  10. Tighten new самоконтрящуюся a nut on 40 Nanometers.
  11. Tighten also on 40 Nanometers of a counternut.
  12. Check up a convergence of wheels.

Replacement of cross-section steering draught in gathering

This work sometimes is not possible because of inaccessibility of screw connection between cross-section steering draught and the steering mechanism. For this screw connection there is key V.A.G 1923, allowing to tighten this screw connection on 100 Nanometers. It is recommended for application.

 PERFORMANCE ORDER

  1. Separate a head of cross-section steering draught from steering сошки how it is described in the previous section.
  2. Loosen the сильфон on cross-section steering draught and the steering mechanism, remove.
  3. Unscrew cross-section steering draught from a lead of the steering mechanism.
  4. Installation: grease the internal hinge with greasing for steering mechanism AOF 063 000 04.
  5. Screw up new cross-section steering draughts on a lead of the steering mechanism on 100 Nanometers.
  6. Establish сильфон.
  7. Fix a head on cross-section steering draught and сошке a wheel how it is described above.
  8. Check up a convergence of wheels.